To keep your Smart Lock working as intended, we recommend calibrating it every 6 months to help it stay aligned with your door. If for any reason you are having trouble with your Smart Lock, calibrating the lock can help get everything synced and running smoothly again. By calibrating the Smart Lock, you are reminding it of the correct locked and unlocked positions on your door so it continues to function properly.
As a first step, you’ll want to make sure that your Smart Lock is powered on and has a functioning battery. The battery for the Smart Lock and its corresponding PIN pad have a lifespan of 8-12 months, depending on usage. If the Smart Lock has an error within the SimpliSafe® Mobile App that indicates there is a low battery or that your Smart Lock is offline, you’ll want to replace the battery before proceeding.
Calibrating the Smart Lock using the SimpliSafe® Mobile App*:
The SimpliSafe® Mobile App may display a Recalibration Needed alert for routine maintenance. You can recalibrate your Smart Lock using the Mobile App on your phone or tablet by taking the steps below:
Tap the tile that reads Recalibration Needed to get started
If you do not see this tile, you can navigate to the Smart Lock device page to manually start recalibration:
Select My System from the navigation bar at the bottom of the app screen
Scroll down to Calibration and tap the arrow to proceed
Click on the Begin button to start the Smart Lock Calibration
The Smart Lock will begin to calibrate. This should take no more than a few minutes to complete
The app will display “Is the Smart Lock unlocked?”
If you notice the door is unlocked, please select YES to proceed
If your door is not unlocked, select NO and proceed with the in-app flow to troubleshoot the issue further
Tap Done to complete the calibration and exit the flow
*In order to recalibrate the Smart Lock from the SimpliSafe® Mobile App, your Base Station must be updated to firmware 2.14 or higher. You’ll also want to make sure that the SimpliSafe® Mobile App is up to date by checking your phone or tablet’s app store for available updates.
Calibrating the Smart Lock using the Keypad:
Bring the Keypad close to the Smart Lock
Press Menu on the Keypad
Enter your Primary PIN
Use the right arrow to toggle to the Devices menu
Choose Lock
Select Recalibrate
When prompted by the Keypad to “Close your Door” - manually turn the lock to a locked position and select Done
The Smart Lock will then automatically turn three times during calibration
If the calibration was successful, the Keypad will display “Check your Door, is it Unlocked?”
If you notice the door is unlocked, please select YES to proceed
The Keypad will now display “Congratulations” on it. You can press OK to exit the flow
Your Smart Lock is now calibrated and you can use it again
Troubleshooting Recalibration Errors
If the Smart Lock fails to recalibrate when using the Mobile App or Keypad, there may be a few reasons for that: the Base Station could not be connected to Wi-Fi, the placement of your Base Station may not be ideal, battery may be low, or it may not be installed properly.
We recommend taking each of the following troubleshooting steps below to successfully calibrate your Smart Lock.
The first thing you should do is check if your Base Station is connected to Wi-Fi. This can be done using either the SimpliSafe® Mobile App or Keypad.
Using the SimpliSafe® Mobile App
Select My System from the navigation bar at the bottom of the screen
The second thing you can test is the placement of your Base Station. We recommend moving and plugging it in as close to the Smart Lock as possible and then resetting the Smart Lock. Once the Base Station has been moved and the Smart Lock has been reset, try calibrating the Smart Lock again. If the calibration is successful, you can move your Base Station back to its original location. But if the calibration is not successful, leave the Base Station close to the Smart Lock while continuing the troubleshooting steps below.
The third thing you should do is check for any available updates to your Base Station or Keypad(s). You’ll know that an update is available when you see a gear icon on the Keypad, or if you receive a notification within the SimpliSafe® Mobile App. You can also manually check for updates within the SimpliSafe® Mobile App by using the following steps:
Next to Firmware, it will say “Update Available” if applicable
Tap on “Update Available” then follow the in-app prompts to start the update process
Once the update is complete, try calibrating your Smart Lock before proceeding to the next step.
If a firmware update is not available, you should check the battery levels of your Smart Lock. To check this, slide the battery cover to the right and press the pairing button located above the batteries. The lights on the device will begin to blink 3 times. Afterwards, if the center light slowly blinks, that would indicate that the batteries within the Smart Lock are low and need to be replaced.
If the above steps do not work, the next step would be to factory reset your Smart Lock.
Slide the battery cover to the right to expose the battery compartment
Press and hold the reset/pairing button located just above the batteries for about 20 seconds
After pressing the pairing button, all 3 lights will flash 3 times in a row. If the lights don’t flash at all, or if the center light then begins to slowly blink, that indicates that the batteries in the Smart Lock need to be replaced.
It’s possible that the Smart Lock has been mounted in a way that has bent the mounting plate. We recommend temporarily removing the Smart Lock from the door, then testing calibration while it’s sitting on a table.
To remove your Smart Lock:
Use the included release tool as a lever to slide the latches of the wings outward on both sides
If you do not have the included release tool, a small object like a SIM card removal tool or small, flat-head screwdriver may also work
Pull the lock off the door
With the Smart Lock in hand, turn it to a locked position and place it on a table
Attempt to calibrate the Smart Lock again using the Mobile App or Keypad
Does the Smart Lock calibrate when on the table?
YES: Remount it, ensuring you do not overtighten it, and attempt to calibrate it on the door again
If the Smart Lock calibrates off the door but not on it
If your Smart Lock calibrated when it was off the door, but after placing it back on the door it fails to calibrate again, that could indicate an issue with the door itself. To identify the issue, calibrate the Smart Lock again with the door open.
If the Smart Lock does calibrate when the door is open, that likely indicates an issue where the door frame or deadbolt do not align with the strikeplate properly. Try moving the strikeplate so it is aligned.
If the Smart Lock does not calibrate when the door is open, the mounting plate may be bent or the deadbolt is not moving smoothly.
To investigate the mounting plate: take down the Smart Lock and slightly loosen the screws securing the mounting plate to ensure it is not bending.
To investigate the deadbolt: clean it using a small brush or condensed air to remove any build-up or debris
Still Need Help?
If your Smart Lock continues to fail calibration after taking the above steps, please contact our support team for additional assistance.
